Inside Acer Predator 17X – disassembly, internal photos and upgrade options

One would assume that the Acer Predator 17X is hard to disassemble and you can’t access all of the hardware that easily since the machine packs a ton of hardware with unusual cooling design and, of course, a lot of storage options. However, this isn’t the case and the Predator 17X is just as easy to teardown as its standard counterpart, the Predator 17. Also, the provided service lid gives access to most of the upgrade options.

You can check here when the notebook appears on the market: http://amzn.to/1Q3JhZG

1. Service lid

It’s a big one and you can’t miss it. As shown in the photos below, opening the service lid gives access to the 2.5-inch HDD (HGST 1TB @7200 rpm), two of the RAM slots supporting up to 16GB each and all three M.2 SSD slots.


DSC09566

DSC09568

DSC09570

DSC09569

Just like last year, the M.2 slots support one 2280 (M key) and one 22110 (B key) standard but also adds a third one positioned right next to the HDD and luckily it’s 2280 (B key) again. All slots should support the PCIe NVMe standard but if you arrange them in a RAID 0 array, the SSDs will use the SATA interface. Our unit came with one 2280 M.2 SSD manufactured by Samsung with model number SM951 (MZVPV256HDGL) with a 256GB capacity supporting the NVMe controller.


DSC09577

DSC09571

DSC09572

DSC09573

2. Removing the bottom piece

If this isn’t enough for you and you are looking for the rest of the hardware such as the Wi-Fi module or battery pack, you should perform almost a full disassembly and as we stated before, it’s not as hard as you’d think. Just remove all the screws and pry up the bottom. Also, keep in mind that the other two RAM slots are located beneath the motherboard. You will have to detach almost everything to turn it around and upgrade or swap the RAM chips. We think that if you unit comes with up to 32GB of RAM, the manufacturer will probably put those chips on the hidden side of the motherboard giving you easy access to upgrade the other two slots on your own.


DSC09609

DSC09562

The Wi-Fi module is located near the right fan (or the left one if you turn it around).

DSC09590

The battery can be found near the bottom left corner of the photo and it’s rated at 88.8Wh.

DSC09593

You can easily spot the loudspeakers positioned on the front and the double subwoofer near the left fan.


DSC09587

DSC09586

3. Cooling system

The cooling system on this thing is just as effective as it’s complicated. Well, it might seem complicated for some but in reality, the whole design is fairly simple.

DSC09583

Here’s the front fan sucking in cool air from outside and distributing it to the rest of the chassis where the other two fans take care of the hot air and drive it out from the back. The cool air should also reach the RAM and storage as well.

DSC09596

There’s also a huge vapor chamber in the middle with several heat pipes.


DSC09580

DSC09582

Acer claims that the main fans will provide up to 15% better air flow and keep the components 9% cooler compared to conventional coolers. That’s because the fans use the so-called AeroBlade technology, which is basically thinner blades. The blades are metal and just 0.1 mm thick.


DSC09588

DSC09591

You can check here when the notebook appears on the market: http://amzn.to/1Q3JhZG

订阅
通知
guest
3 Comments
内线反馈
查看所有评论
Anonymous
Anonymous
5 年 之前

nice breakdown, any chance there is a step by step guide to changing the ram on the slots under the motherboard, so basically you have to remove the whole mother board.

Javier Garza
Javier Garza
5 年 之前

Can you explain why you say the open ssd slots are b keys when the pins are on the left, but it only has 5 pins on the notch. it is my understanding that the b key has 6 pins and the m key has 5. You say it is NVME standard, but everywhere I look says NVME is the m key and has 5 pins on the right side of the sad. Can you please elaborate which ssd will fit. Or do you have to flip the ssd over so it will fit the 5 pins?

Austin Hruskach
Austin Hruskach
5 年 之前

Hello! On the two M.2 slots that are above each other, the bottom one is the one that supports NVMe. The rest are all SATA. So if you have 2 SATA M.2 SSD’s in RAID 0 (Like the default configuration), remove all of the SSDs, put the NVMe SSD into the bottom slot like I mentioned at first, then move the two SATA SSDs into the two remaining M.2 slots. Then reassemble the case and power it up. It’ll boot like normal. This is how my 17X is set up right now!